Happymodel Mobeetle6 Whoop and Toothpick 2-IN-1 FPV-Racer-Drohne

Description: The DiamondF4 Flight controller and The Mobeetle6 were inspired from Angry Don FPV, we really appreciated for his help to Happymodel and to this hobby. We also very expecting to the performance of this BNF with the new Diamond F4 ELRS flight controller. Specifications: Brand Name: Happymodel Item Name: Mobeetle6 whoop and toothpick 2-IN-1 FPV Racer DroneWheelbase: 65mm Size: 80mm*80mm*30mm Weight: 17.5g (without battery) Features: The lightest 1S Whoop and Toothpick 2-IN-1 fpv droneComes with tooth pick frame for convertPowerful and efficiency The lightest 1s AIO 5IN1 F4 flight controllerNew Unibell SE0702 brushless motors with pcb wire board Built-in OPENVTX up to 400mwLow profile Canopy design Package includes: Item Name Qty 65mm whoop Frame (Mobula6 frame)1 65mm toothpick frame(Mobeetle6 frame)1 Option1: DiamondF4 ELRS built-in SPI ELRS receiver1 Option2: DiamondF4 FR built-in SPI FRSKY receiver SE0702 KV23000 Unibell brushless motor4 Gemfan 1210 31mm propeller(4cw+4ccw)1 Runcam Nano31 Built-in 5.8G 48ch 25mw-400mw OPENVTX1 1s 300mah Lipo battery 2 Mobula6 canopy1 Propeller disassemble tool1 Screwdriver1 Spare parts specifications:Motor Mode:SE0702 KV23000 Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ9.5mm*14mm Weight(g):1.5g No.of Cells(Lipo):1S onlyPropeller Weight:0.19g Material:PC Pitch:1 inch Props Dia:30mm Center Hole Dia:1mmFlight controller (ELRS SPI RX version)DiamondF4 ELRS FC Firmware target: CrazybeeF4SX1280 (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000 or ICM20689 or BMI270(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G OPEN VTX Built-in SPI ELRS V2.0/Frsky receiver Built-in 5V 1A BECOnboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_50_REV16_8.HEX Default protocol: DSHOT600Onboard SPI ExpressLRS 2.4GHz Receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V2.0 RF Frequency: 2.4GHz Antenna : Enameled copper wire antenna Telemetry output Power: <12dBm Receiver protocol: SPI ExpressLRS Compatible with ExpressLRS V2.0 TX Module Couldn’t flash separately ExpressLRS firmwareOnboard Frsky SPI D8 receiver Version SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300mOnboard 5.8g OPENVTX Firmware version: OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw)Runcam Nano3 Model: RunCam Nano 3 Image Sensor: 1/3" CMOS Horizontal Resolution: 800TVL Lens : 2.3mm(M6.5) FOV 140° Signal System: NTSC S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: 0.01Lux@1.2F D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: 110mA@5V 120mA@3.3V Housing Material: ABS Net Weight: 1.2g Dimensions: L14mm*W14mm*H9mmLipo Battery Capacity:300mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 57mmx12mmx7mm Weight: 7.5g Connector: PH2.0

Price: 148.35 USD

Location: 深圳

End Time: 2024-02-22T09:12:04.000Z

Shipping Cost: 0 USD